How to Convert MP3 to DAISY on a Mac (For CD, SD Card and USB Players)
The player sits on the kitchen table. It has big tactile buttons, a CD slot, and one job: reading books to someone who cannot see the screen you are reading this on. You have the book as a folder of MP3 files. You burn them to a disc, the player takes it, and it plays. From the top, one file after the other. The skip key moves from file to file, but the player has no idea it holds a book: no title to announce, no headings to move by, nothing smaller than a whole track.
That is not a broken player. It is the player doing exactly what a folder of MP3s allows.
What the player wants is a DAISY book: the same audio, plus a small set of navigation files that tell it where every chapter starts. Ask how to make one on a Mac and you can end up, as one TidBITS forum thread did, with the advice that the player accepts MP3 files anyway, which is where you started. There is a free way to do it, and since version 1.4.4 AudioBo does it too. Both are below, along with the part no converter does for you: getting the book onto a CD, an SD card or a phone in a way the player recognizes.
A DAISY book is your MP3s plus a table of contents the player can read. Without that table, the player treats the disc like any music CD: it plays, and the skip key steps from track to track, but there is no book to announce and no levels to move by. With it, the player announces the book when the disc goes in and lets the listener jump between chapters and, if the book marks them, between phrases within a chapter.
The audio itself should be plain: MP3 at a constant bitrate, and by convention one channel. A book recorded at 64 kbps fits on one CD up to about 22½ hours with a safety margin, about 25½ on a full disc; at 32 kbps, about twice that.
The last step is where most attempts go wrong. A CD has to be a data CD with the book's files at the very top of the disc, not inside a folder. An SD card follows the player's own folder rules, which differ by brand.
Rather not assemble the navigation files by hand? AudioBo builds a DAISY talking book from the chapters you already have: one choice in the Presets menu sets the audio the way DAISY players expect, adds a spoken title read by a voice on your Mac, and writes the table of contents.
It does not burn the disc and it does not remove DRM. Putting the finished folder on a CD or card is covered further down this page.
A folder of MP3s is not a DAISY book
DAISY is the format libraries for blind and low-vision readers use for talking books; what the DAISY format is covers its history and versions. This page is about one version of it, DAISY 2.02, because it is the version every player and tool on this page handles.
A DAISY 2.02 audiobook is a folder with three kinds of files in it. The audio is ordinary MP3. Next to it sits a file called ncc.html, the navigation control center, which lists every heading in the book. And for each section there is a small SMIL file that ties a heading to a stretch of audio with exact start and end times.
Take those files away and the player is left with a pile of tracks. The author of Anemone, a free DAISY tool, warns that if a Victor Reader Stratus 4 cannot find the book’s files where it expects them, it “will not recognise the CD as a Daisy CD and will just play the MP3s”. The Plextalk PTN2 handbook describes the same fallback from the other side: a plain MP3 folder plays in file-name order, and the only navigation is skipping tracks.
Navigation by chapter is the whole point of the format, and it comes from the chapters you put in. If your source is one long MP3 with no chapter marks, a DAISY book made from it has a single chapter heading, so there is nowhere to jump to. Fix that first: an audiobook with no chapters explains how to tell whether a file has any, and editing metadata, cover and chapters covers adding them. If the book is still on a stack of audio CDs, ripping the set comes before any of this.
Which tools make one, and which run on a Mac
The tool people search for by name is Obi, the DAISY Consortium’s free authoring program. It imports existing audio, splits it into phrases at the pauses, and writes DAISY 2.02. NNELS, the Canadian accessible library, documents converting MP3 audiobooks with it, and its install step reads “(Windows only)”.
| Tool | Runs on | Builds DAISY 2.02 from existing audio |
|---|---|---|
| Obi (DAISY Consortium, free) | Windows only | Yes, with phrase detection on import |
| Tobi (DAISY Consortium, free) | Windows | No, it targets DAISY 3 and EPUB 3 |
| Dolphin Publisher | Windows | Yes |
| Anemone (free, open source) | Anywhere with Python 3, Mac included | Yes, from the command line |
| AudioBo 1.4.4 | Mac | Yes |
If there is a Windows PC in the house and an afternoon to learn a new program, Obi is free and made by the people who maintain the standard. Use it.
On a Mac without Windows, the free route is Anemone. It is “a Python 3 script to put together a DAISY digital talking book, from HTML text and MP3 audio recordings”, DAISY 2.02 by default. For an audio-only book it wants one MP3 per section, titled from the file names or a separate text file. It installs with pip install anemone-daisy-maker, has no window, and its --mp3-recode option re-encodes the MP3s to a constant bitrate for pickier players; that option needs LAME, or the miniaudio and lameenc Python modules, installed as well. If you are comfortable in Terminal, that is a complete answer and it costs nothing.
The audio settings DAISY players expect
DAISY players are MP3 players with strong opinions, and a book that ignores them can play and still misbehave.
Constant bitrate, not variable. The DAISY 2.02 specification calls variable bitrate “not recommended”. In practice it is worse than that wording suggests: the PTN2 handbook says a VBR book plays but reports elapsed and remaining time wrongly, and Anemone’s notes say JAWS FSReader 3 seems to need its --mp3-recode option to keep the audio in sync, and the US NLS player navigates only with that option.
Mono, 44.1 or 22.05 kHz. DAISY 2.02 allows stereo, but narration does not need two channels and mono is the convention. Obi’s defaults are mono, 44.1 kHz and, when it exports MP3, 64 kbps, and NNELS’s own conversion advice sets 64 kbps as the minimum. Stay at 44.1 or 22.05 kHz: the later DAISY 3 standard only requires players to handle 44.1, 22.05 and 11.025 kHz, and 48 kHz is not on that list.
Nothing heavy at the start of the file. Anemone’s source carries the warning that players like FSReader “can get timing wrong if mp3 contains too many tags at the start (e.g. images)”. A cover picture embedded in every chapter file is exactly that. The DAISY Consortium’s own sample book has no tags at all.
How bitrate trades against size in general is on audiobook bitrate and output settings. For DAISY the extra question is whether the book fits on a disc.
How much fits on one CD
Size is bitrate times length, so the capacity of a CD can be worked out rather than guessed. The table assumes a 700 MB CD-R; the first column leaves a margin by stopping at 650 MB, which is also where AudioBo’s CD warning starts.
| Bitrate, mono | Up to 650 MB | Full 700 MB disc |
|---|---|---|
| 64 kbps | about 22½ hours | about 25½ hours |
| 48 kbps | about 30 hours | about 34 hours |
| 32 kbps | about 45 hours | about 51 hours |
These are estimates from the arithmetic, not from a burned disc, and the navigation files add a little on top. They line up with what libraries say: RNIB describes DAISY CDs that “hold around 25 hours of audio”, close to what 64 kbps gives on a full disc. Treat the 48 and 32 kbps rows as a fallback for a book that would not fit otherwise: NNELS’s conversion advice sets 64 kbps as the minimum.
A book longer than that has two honest options. Lower the bitrate, or skip the CD and use an SD card or USB stick if the player has a slot or port for one. NNELS gives librarians the same advice when a book is too big for a disc.
Building a DAISY book in AudioBo
Everything above can be done with Anemone. The cost is a dozen settings that all have to be right at once, and a listener who finds the mistakes for you. That is the part AudioBo takes over, starting with version 1.4.4.
You bring in the MP3s the way you would for any audiobook, and each file becomes a chapter unless you set chapters from a CUE sheet or timestamps instead. Then, in the Build window, on the Custom tab, open the Presets menu and choose DAISY (Talking Book).
That one choice sets the audio the way the sections above describe. It becomes MP3, mono, constant bitrate, starting at 64 kbps (lower if your source is lower) and 44.1 kHz, or 22.05 kHz for a source below that. Every chapter is re-encoded so the whole book matches. Tags and cover art are left out of the audio files. You can still change the bitrate, channels or sample rate; the preset stays on and marks itself as edited, and the sample rate menu offers only 44.1 and 22.05 kHz.
Spoken Title decides what the player announces when the disc goes in (more on that below). Read by Mac has a voice on your Mac read the book’s title and author and places that recording before chapter one. The Language row picks the language, and also sets the book’s Language in its metadata; the Voice row picks the voice, where Automatic takes the best one installed for that language, and you can listen before you build. Voices are free to add in System Settings › Accessibility › Spoken Content, under System Voice › Manage Voices. Use First Chapter adds no voice and lets chapter one stand in, which suits a book with its own recorded introduction. With no language set, or no voice installed for it, AudioBo says so and falls back to the first chapter.
One warning can appear when you press Build, and only when something applies. It covers two cases: the estimated size is past 650 MB, the safe figure for one CD from the table above; or the book has more than 1,024 files, the most the Plextalk PTN2 reads in one folder. A DAISY book uses two files per chapter, so the second case starts somewhere above 500 chapters. If both apply, the one alert lists both. It offers Build Anyway or Cancel, and a “Don’t show this again” box.
What comes out is a folder: 0001.mp3 onward for the chapters, a .smil file beside each one, plus ncc.html and master.smil. When Read by Mac recorded a spoken title, it is 0000.mp3, with its own .smil, ahead of chapter one. AudioBo also listens for pauses in each chapter and marks them, so a player’s phrase key moves from pause to pause instead of a whole chapter at a time.
What it does not do:
- Phrases come from detected pauses. You cannot place them by hand.
- Every chapter is a top-level heading; no parts with chapters nested inside.
- One book is one disc. No numbered multi-CD sets: a book that does not fit goes on a card or stick, or drops to a lower bitrate.
- Audio only, no text for the player to show.
- Re-encoding is always on, so MP3 sources pay one more generation of compression. In narration at these bitrates it is hard to hear, but it is real.
AudioBo does not remove DRM, so a book bought from Audible or Apple Books cannot become a DAISY book this way; converting M4B to MP3 explains why no converter can open those.
Putting the book on a CD
Two rules decide whether the player sees a book or a pile of tracks.
Burn a data CD, not an audio CD. HumanWare’s instructions for its CD players say exactly this: “burn a data CD not an AudioCD”. An audio CD turns the MP3s back into CD tracks and leaves the navigation files behind.
Put the files at the top level of the disc, not in a folder. Anemone’s documentation is blunt about it: the files “need to be written to the top level of the CD, not to a folder on it”, or the Stratus 4 plays the MP3s without the book. Some burning programs, handed a folder, put the folder itself on the disc. That is the wrong result here.
Whatever you burn with, check the disc before it goes in the post. Open it on the Mac. ncc.html, master.smil and the numbered MP3 and SMIL files should be visible the moment the disc opens, with no folder to click into first. If they are inside a folder, burn again.
Use a CD-R. A DVD holds more, but do not count on one: NNELS suggests a DVD only for devices known to play DVDs.
Putting the book on an SD card or USB stick
Cards and sticks hold far more than a CD. The rule everywhere is one folder per book; where that folder goes depends on the player.
| Player | Where the book folder goes |
|---|---|
| Victor Reader Stream | SD card: inside the $VRDTB folder, in its own subfolder. The Stream creates its $VR folders when you insert a card that is not write-protected. |
| Victor Reader Stratus | SD card or USB stick: inside $VRDTB, in its own subfolder. On a USB stick the Stratus does not create $VRDTB, so make that folder yourself. |
| Plextalk PTN2 | Any folder, one per book. Subfolders inside a book are ignored. |
| Milestone 312 Ace | Any folder, one per book. |
Keep to those folders even where something else seems to work. On the Stream, Anemone’s notes say a book copied loose to the top of the SD card still plays but loses section navigation; for a USB stick they put the book at the top level of the stick. HumanWare’s Stratus FAQ does accept DAISY books at the top of the SD card, but the player then stops looking for any other files there.
Keep the card at 32 GB or less for older players. HumanWare lists the Stratus as compatible with SDHC cards up to 32 GB, and the PTN2 reads SD and SDHC only.
Do not rename files inside the book folder. The folder name is yours to change; it only affects sort order on the player, and the book’s spoken title comes from the book itself.
Phone apps and a quick check on the Mac
Phone and tablet apps take a DAISY book as a single ZIP file, one ZIP per book. Dolphin EasyReader asks for “DAISY 2 (zipped)”, and Voice Dream Reader imports a ZIP and plays the recorded audio of an audio-only book. Finder’s Compress command on the book folder makes a ZIP.
Before you burn anything, there is a cheaper test. Thorium Reader, a free reader for Mac, Windows and Linux, opens a DAISY book from its ncc.html file, and its code treats an audio-only DAISY 2.02 book as an audiobook. If the chapters appear in the right order there, the navigation files are doing their job.
What the listener hears
When a DAISY CD goes into a Victor Reader Stratus 4, its guide says the player “will announce the title and start playing the book”. The DAISY 2.02 specification requires the book’s first heading to be its title section, and players that name a book this way play the audio recorded there. If that section is chapter one, the listener is likely to hear the start of chapter one each time the player names the book. The DAISY Consortium’s own sample book, like many library books, opens with a short recorded title instead.
From there the navigation keys move through levels. In the Stream’s guide, level 1 usually means chapter, and a phrase level is always offered below it, capped at one-minute jumps. The Milestone 312 Ace opens a book at the phrase level by default. Place and bookmarks are kept by the player, so nothing about them has to be built into the book.
That is the difference a folder of MP3s cannot make: a player that knows it holds a book, names it, and moves through it by chapter and by phrase.
Common questions
Can you convert MP3 to DAISY on a Mac?
Yes. The DAISY Consortium's own free tool, Obi, is Windows only, but Anemone, a free Python script, runs anywhere Python 3 does, including a Mac, and builds an audio-only DAISY 2.02 book from one MP3 per section. It works from the command line. AudioBo 1.4.4 does the same from a window, with its DAISY (Talking Book) preset.
Will a DAISY player play a plain folder of MP3s?
Usually, yes, but only as a list of tracks. Without the ncc.html navigation file and the SMIL files beside the audio, the player has nothing that tells it where chapters start. A Victor Reader Stratus 4 will not recognize such a disc as a DAISY book, and a Plextalk PTN2 plays the files in name order with track skipping only.
Should a DAISY CD be burned as an audio CD or a data CD?
A data CD. HumanWare's own instructions for its CD players say to burn a data CD, not an audio CD. The book's files also have to sit at the top level of the disc rather than inside a folder, or a Stratus 4 plays the MP3s without the book's navigation.
How many hours of audio fit on one DAISY CD?
Roughly 22½ to 25½ hours at 64 kbps mono, and 45 to 51 hours at 32 kbps, depending on whether you leave a safety margin on a 700 MB disc. These are estimates from the bitrate, not measurements of a burned disc. RNIB describes DAISY CDs as holding around 25 hours of audio, close to what 64 kbps gives on a full disc.
Can I turn an Audible audiobook into a DAISY book?
Not with AudioBo. Books bought from Audible or Apple Books are locked to those stores' apps, and AudioBo does not remove DRM and never will. A DAISY book has to start from audio files you can open and play outside the store's app, such as MP3s that came without protection.